How to work it out
Sheet length
Each sheet runs from the eave to the ridge. Half the width plus the eave overhang, divided by the cosine of the pitch, plus 50 mm into the spouting. For the example: (4 + 0.6) ÷ cos 20° + 0.05 = 4.95 m.
Number of sheets
The roof length (including any gable overhang) ÷ the sheet cover, rounded up, for each slope. Corrugate covers 762 mm, so 12.6 m needs 17 sheets a side — 34 in all.
Hip roofs
Takeoff works along each slope sheet by sheet. Sheets against a hip are ordered at their longest edge and cut on site, and the smallest corner pieces come from those offcuts.
Flashings and fixings
Ridge, hip, valley and barge lengths come from the roof shape and pitch, plus 5% for laps. Roofing screws are counted at five per corrugate sheet (four for 5-rib) at every purlin.
Find my roof
Type an address and Takeoff uses aerial data to suggest the roof shape, size and pitch. It can’t see under the eaves, so always check the numbers before ordering.
Worked example
A 12 × 8 m house with a gable roof at 20°, 600 mm eaves and 300 mm overhang at the gable ends. Corrugate in COLORSTEEL®, with netting and underlay.
| Item | Qty |
|---|---|
| Roofing iron | |
| Corrugate roofingCOLORSTEEL® · 0.40 BMT · cut to length · 34 sheets: 34 × 4.95 m | 168.3 lm |
| Flashings | |
| Ridge & hip cappingMade to order · COLORSTEEL® · 12.6 m of ridge · + 5% for laps | 13.3 lm |
| Barge flashingMade to order · COLORSTEEL® · 4 sloping edges at the gable ends · 19.6 m + 5% | 20.6 lm |
| Fixings | |
| Roofing screws12g × 65 mm hex head with washer · Class 4 · 5 per sheet at every purlin (900 mm centres) + 10% | 1309 screws |
| Flashing fixingsStitching screws or sealed rivets · box of 100 · 118 · about 1 every 300 mm along the flashings | 2 boxes |
| Underlay & netting | |
| Roof underlaySelf-supporting synthetic roof underlay · roll · 123.4 m² + 10% for laps · ≈40 m² per roll | 4 rolls |
| Roof nettingGalvanised or poly roof netting · roll · Run over the trusses or rafters to hold up the underlay · ≈70 m² per roll | 2 rolls |
This is the list Takeoff produced for that job. Your list will change with your sizes and settings.
Check before you buy
- Sheets are cut to length (eave to ridge, plus 50 mm into the spouting) and sold by the lineal metre. Your roll-former confirms lengths and covers for their profile.
- Gable roof: ridge runs along the length. Barges are on both gable ends.
- Flashings are made to order and listed in lineal metres. Spouting is on the Spouting tab; purlins and battens on your plans aren’t included here.
- Quantities only — follow the roofing manufacturer’s installation guide, the NZ Metal Roof and Wall Cladding Code of Practice and your plans for pitch, fixings and flashings.
What the calculator covers
- Gable, hip and skillion roofs
- L- and T-shaped houses, with valleys where the wings meet
- Any pitch, with a warning below the profile’s minimum
- Corrugate and 5-rib profiles
- COLORSTEEL®, ZINCALUME® or COLORSTEEL® Maxx® for the coast
- Sheets cut to length for every slope
- Ridge, hip, barge and apron flashings
- Roofing screws, flashing fixings, underlay and netting
- Find my roof from the address (beta)
Questions
How many roofing sheets do I need?
For each slope, divide the roof length (including overhangs) by the sheet cover — 762 mm for corrugate — and round up. The 12 × 8 m gable roof on this page needs 34 sheets of 4.95 m.
How do I work out the length of a roofing sheet?
Take the horizontal distance from the fascia to the ridge, divide by the cosine of the roof pitch, and add about 50 mm to run into the spouting.
What is the minimum pitch for corrugated iron?
Corrugate generally needs at least 8°. Trapezoidal (5-rib) profiles go down to about 3°. Check the manufacturer for the exact figure for your profile and span.
Do I need underlay under a long-run roof?
Yes — a roof underlay is normal practice under metal roofing in NZ, with netting over open trusses or rafters to hold it up.
Get your own list in under a minute
Put in your sizes. Print it, save it as a PDF, email it or take it to your supplier.
Start your roofing list