How to work it out
Rafter size and spacing
The rafters span from the ledger on the house to the front beam. Takeoff picks the smallest common size that typically spans that far: 600 mm centres for an open pergola, 900 mm under a roof. For the example, 3 m at 600 mm needs 190 × 45.
Beam and posts
Posts go at no more than about 3 m centres along the beam. The beam is doubled, one each side of the posts and bolted through, and sized from the post spacing and how much roof it carries.
Shade battens or roofing
An open pergola gets 50 × 50 battens at 300 mm across the rafters. A covered veranda gets 70 × 45 purlins (900 mm for polycarbonate, 1200 mm for iron) and sheets that run from the house to the front with at least 5° of fall (8° for corrugated iron).
Fixings and footings
Joist hangers at the ledger, a Lumberlok Multigrip where each rafter crosses the beam, two M12 bolts through each post, and post concrete worked out from the hole size.
Worked example
A 6 × 3 m open pergola fixed to the house, 2.4 m high, with 50 × 50 shade battens and posts concreted into the ground. Everything else is on the suggested settings.
| Item | Qty |
|---|---|
| Framing | |
| Posts125×125 H5 · 3.6 m · 3 per beam at 3 m centres · 900 mm in the ground | 3 posts |
| Beam190×45 H3.2 · 6.0 m · Doubled (2/190×45), one each side of the posts · along the front · joined over a post | 3 lengths |
| Ledger (house side)190×45 H3.2 · 6.0 m · Same size as the rafters · bolted to the house framing | 1 length |
| Rafters190×45 H3.2 · 3.6 m · 11 rafters at 600 mm centres · 3.3 m each incl. 300 mm overhang | 11 lengths |
| Shade battens50×50 H3.2 · 4.8 m · 11 rows at 300 mm along the rafters · 68.2 lm + 5% | 15 lengths |
| Fixings | |
| Joist hangersTo suit 45 × 190 rafters · hot-dip galv · One for each rafter at the ledger (+5%) | 12 hangers |
| Ledger to house fixingsM12 galv bolts or coach screws, with washers · ≈1 every 600 mm + each end — into the house framing, not just the cladding | 11 bolts |
| Lumberlok Multigrip38×38×125 · hot-dip galv · One per rafter at each beam (11 +5%) — use two where wind uplift is high | 12 multigrips |
| Lumberlok product nails30×3.15 · hot-dip galv · 500 g bag · ≈207 nails for hangers and Multigrips | 1 bag |
| Beam to post boltsM12 × 260 galv bolt, nut & 2 washers · 2 through each post and both beam halves | 6 bolts |
| Batten screws10g × 100 mm galv timber screws · box of 500 · 255 · 2 where each batten crosses a rafter | 1 box |
| Footings | |
| Post concrete20 kg premix concrete bags · 3 holes 400 Ø × 900 mm · 0.33 m³ incl. 10% | 35 bags |
This is the list Takeoff produced for that job. Your list will change with your sizes and settings.
Check before you buy
- Suggested sizes: rafters 190×45 at 600 mm, beam 2/190×45 with posts at 3 m, 125×125 posts. These are typical sizes for a pergola in a low to medium wind zone — check spans, post footings and fixings against NZS 3604 (or have it engineered) for your site, wind zone and any snow.
- The ledger must be bolted through to the house framing, with spacers or a flashing so water can’t sit behind it. Check the detail for your cladding with your builder.
- Check with your council whether you need a building consent — many pergolas and small verandas are exempt, but conditions apply (size, height and distance from the boundary).
What the calculator covers
- Open pergolas and covered verandas
- Fixed to the house or freestanding
- Suggested rafter, beam and post sizes you can change
- Shade battens, or purlins with polycarbonate or long-run iron
- Apron and barge flashings, plus spouting along the front
- Posts concreted in, or on pads with post anchors
- Galvanised or stainless fixings for the coast
- A plan drawing with every rafter and post
Questions
What size rafters do I need for a pergola?
It depends on the span and spacing. As a rough guide at 600 mm centres, 140 × 45 spans about 2.6 m, 190 × 45 about 3.5 m and 240 × 45 about 4.4 m. Under a roof at 900 mm centres the spans are shorter. Check NZS 3604 or your builder for your wind zone.
How far apart should pergola posts be?
Usually no more than about 3 m, with the beam sized to suit. Wider spacing needs a deeper beam; Takeoff suggests one from the spacing and the roof it carries.
What is the minimum fall for a polycarbonate veranda roof?
Corrugated polycarbonate generally needs at least 5°, and corrugated iron about 8°. Takeoff warns you if the fall you enter is too flat.
Do I need a building consent for a pergola or veranda?
Many pergolas and small verandas are exempt, but conditions apply around size, height and distance from the boundary. Check with your council before you build.
Get your own list in under a minute
Put in your sizes. Print it, save it as a PDF, email it or take it to your supplier.
Start your pergolas & verandas list