How to work it out
Sheets
For each wall, pick the sheet length that covers it with the fewest joins, then take off doors and windows. Ceilings are laid out the same way. Takeoff only uses sizes on the GIB selector chart.
Spare sheets
A 5% spare is only added once it adds up to a whole sheet, and it is labelled on the list — so a small room doesn’t get an extra sheet it doesn’t need.
Screws and glue
Screw count depends on the board, the framing and the fixing pattern. Takeoff picks the screw length for the board thickness and framing type — timber or steel.
Stopping
Tape and compound come from the length of joints and internal corners.
Worked example
A 5 × 4 m lounge (one door, two windows) and a 3.6 × 3 m bedroom (one door, one window). 2.4 m studs, 10 mm walls, 13 mm ceilings, timber framing.
| Item | Qty |
|---|---|
| Plasterboard | |
| GIB Standard10 mm · 3600 × 1200 · TE/TE · SKU 11540 | 4 sheets |
| GIB Standard10 mm · 3000 × 1200 · TE/TE · SKU 11538 | 4 sheets |
| GIB Standard13 mm · 3000 × 1200 · TE/TE · SKU 11550 | 3 sheets |
| Fixings | |
| GIB Grabber screws6g × 32 mm · High Thread (timber) · loose · box of 200 · 209 screws for 10 mm walls | 2 boxes |
| GIB Grabber screws6g × 41 mm · High Thread (timber) · loose · box of 200 · 116 screws for 13 mm ceilings | 1 box |
| GlueGIBFix One · 375 mL cartridge · 1.6 L needed · ≈4 L per 100 m² | 5 cartridges |
| Stopping | |
| Paper jointing tapeGIB paper tape · 75 m roll · 47 m of tape: 19.2 m of joints + 22.8 m of corners and angles | 1 rolls |
| Jointing compound15 L pail (e.g. GIB Trade Finish Multi) · ≈70 m of joint per pail, all coats | 1 pails |
This is the list Takeoff produced for that job. Your list will change with your sizes and settings.
Check before you buy
- Sheets are worked out wall by wall to waste the least board. No spare added — 5% of 11 sheets is less than one sheet. Offcuts can often be reused around windows and doors.
- Joint, tape and compound figures are estimates based on GIB’s fixing and finishing guides.
- Bracing walls need GIB Braceline or the board and fixing pattern on your plans — check before ordering.
What the calculator covers
- GIB Standard, Aqualine, Braceline, Noiseline and Fyreline per room
- Tapered or tapered/square-edge sheets
- Wardrobes, gables, raked ceilings, bulkheads and odd areas
- Timber or steel framing
- GIB Grabber High Thread or Self Tapping screws
- GIBFix and All-Bond adhesives
- Rondo ceiling battens
- Paper tape and compound
Questions
How many sheets of GIB do I need for a room?
Work out the wall and ceiling area, take off doors and windows, and divide by the sheet size — then round up wall by wall. For the lounge and bedroom on this page that is 31 sheets including one spare.
What thickness of GIB for walls and ceilings?
10 mm is common on walls and 13 mm on ceilings, but your plans or bracing design may say otherwise. Bracing walls need GIB Braceline or the board on your plans.
How many GIB screws per sheet?
It depends on the sheet size and fixing pattern. Takeoff counts screws from the area and GIB’s fixing guide, then rounds to whole boxes.
Get your own list in under a minute
Put in your sizes. Print it, save it as a PDF, email it or take it to your supplier.
Start your GIB list