How to work it out
Area
Each wall is length × height, plus half the length × the gable peak for a gable end, less each window and door at its actual size. Head flashings are cut to each opening’s width plus 50 mm each side.
Lineal metres
Area ÷ the board’s cover (not its face width) + 10%. A 180 × 18 bevelback covers 148 mm once lapped, so 93.7 m² needs 93.7 ÷ 0.148 = 633 m, or 697 m with the allowance. Covers come from the Southern Pine Products pocketbook.
Sheets
Shadowclad, ply and fibre cement go vertically, 1200 mm cover per sheet. Takeoff picks the shortest sheet that covers the wall height and adds a Z flashing where a wall is taller than a sheet.
Iron
Long-run corrugate or 5-rib runs vertically: one sheet per cover width, each cut from the bottom of the wall to the top, with gable sheets cut to the rake. You get a cutting list, screws at every nog row, and made-to-order corner, base and barge flashings.
Fixings
One nail or screw per board at every stud. Lengths start from the SPP chart and go 20 mm longer through a cavity. Galv by default, stainless within 500 m of the sea, and always stainless for H3.2 cladding.
Worked example
A simple single-storey house: two 12 m walls and two 8 m gable ends, 2.4 m high, with 7 windows, a front door and a 2.4 m slider, each entered at its own size. 180 × 18 bevelback weatherboard on a 20 mm cavity, timber box corners, galv nails.
| Item | Qty |
|---|---|
| Cladding | |
| Bevelback weatherboard180 × 18 · pre-primed pine H3.1 · 148 mm cover · 93.7 m² ÷ 148 mm cover = 632.8 m + 10% · your merchant works out the lengths (random or finger-jointed) | 697 lm |
| Corners & joins | |
| Back soakersBehind every butt join · to suit 180 board · 121 joins (boards ≈5.4 m long) + 10% | 134 each |
| Timber box cornerPrimed pine · 4 corners × 2.4 m + 10% | 11 lm |
| Fixings | |
| Weatherboard nails100 × 3.15 mm plain shank · hot-dip galv · box of 500 · 1161 nails · 1 per board at every stud + 10% | 3 boxes |
| Wrap & cavity | |
| Building wrap (wall underlay)Roll · 110.4 m² of wall + 10% · ≈25 m² per roll after laps | 5 rolls |
| Building wrap tapeFor laps, tears and around openings · Approx. | 2 rolls |
| Cavity battens20 mm · H3.1 · e.g. 45 × 20 · On every stud, and beside each opening, + 10% | 239 lm |
| Cavity closer / vent stripAlong the bottom of the cladding and over every opening · 40 m of base + opening heads, + 10% | 57 lm |
| Flashings | |
| Head flashingAluminium · cut to opening width + 50 mm each side · 1 × 2500 mm, 1 × 1900 mm, 5 × 1300 mm, 1 × 960 mm, 1 × 700 mm | 13.2 lm |
| Flexible flashing tapeSill and jamb tape · 25 m roll · Window sills, jamb corners and door jamb corners | 2 rolls |
This is the list Takeoff produced for that job. Your list will change with your sizes and settings.
Check before you buy
- Weatherboard covers are from the Southern Pine Products pocketbook. Fixing lengths start from SPP’s chart (75 mm for bevelback) and go 20 mm longer through a cavity — confirm with your supplier.
- Punch nails 3–4 mm below the surface, then fill and prime.
- Hot-dip galv fixings are listed. Use stainless (304 or 316) within 500 m of the sea or a tidal estuary.
- Quantities only. Flashings, cavity details and fixings must follow the manufacturer’s installation instructions, E2/AS1 and your consented plans — always check the product information with your supplier.
- Paint or stain the cladding on the Paint tab (exterior).
What the calculator covers
- Bevelback weatherboards, 135 to 240 mm
- Scallop, bevelled and Wellington rusticated weatherboards
- Shadowclad Ultra or Natural, Groove or Texture
- H3.2 structural ply, 9 or 12 mm
- Fibre cement sheet, grooved or smooth
- Long-run corrugate or 5-rib iron, run vertically
- Gable ends, and each window and door at its own size
- Timber box corners, D4S facings with scribers, or corner soakers
- Back soakers at every join
- Nails, jolt screws or stainless trim head screws
- Building wrap, cavity battens, cavity closer and flashings
Questions
How many lineal metres of weatherboard per square metre?
Divide 1000 by the board’s cover in mm. A 180 bevelback (148 mm cover) needs about 6.75 m per m². A 180 rusticated board (155 mm cover) needs about 6.45 m. Add around 10% for offcuts.
What is weatherboard cover?
The height of wall each board actually covers once it laps the board below. It is always less than the face width — a 180 mm board covers about 148–155 mm depending on the profile.
Do I need a cavity behind weatherboards?
For new work in most of NZ, yes — a 20 mm drained cavity is normal under E2/AS1. Direct fixing only suits low-risk walls. Check your consented plans.
Galvanised or stainless nails?
Hot-dip galv is fine for H3.1 pre-primed weatherboards away from the coast. Within 500 m of the sea or a tidal estuary, use stainless. H3.2 treated cladding needs stainless everywhere.
Get your own list in under a minute
Put in your sizes. Print it, save it as a PDF, email it or take it to your supplier.
Start your cladding list