How to work it out
Poles and footings
One H5 round pole at every bay line on each pole row, cut from stock lengths to suit the height plus the embedment (1.2 m by default), set in concreted holes. A middle row is added when the shed is over 6 m deep so no roof span is over 6 m.
Frame
A pair of beams along each pole row, sized to the bay width, and a pair of rafters (or a truss for a gable roof) bolted to every pole line.
Roof
Purlins on edge between the frames at up to 900 mm centres (closer in very high wind zones), then the roofing iron, flashings and screws from the roofing calculator.
Walls and doors
Girts between the poles on every clad side, a H4 skirt board, and wall iron with a cutting list that follows the roof slope and leaves out the openings. Roller doors, PA doors and windows each get their framing and flashings.
Worked example
A 3-bay mono-pitch farm shed, 10.8 × 6 m with 3.6 m bays, open at the front and clad in corrugate on the back and both ends, 2.7 m to the eaves with a 5° pitch and a PA door in one end. Everything else is on the default settings.
| Item | Qty |
|---|---|
| 1 · Poles & footings | |
| Round poles175 mm SED · H5 · 4.8 m · 1200 mm in the ground + height to the roof framing | 8 poles |
| Pole footing concrete20 kg premix concrete bags · 8 holes Ø450 × 1200 mm · 1.43 m³ incl. 10% | 151 bags |
| Auger hirePost-hole borer / tractor auger, Ø450 mm · 8 holes | 1 day |
| 2 · Frame | |
| 200×50 SG8 H3.26.0 m · Eave / ridge beams — a pair on each pole row, 2 rows, joins over the poles | 4 lengths |
| 200×50 SG8 H3.24.8 m · Eave / ridge beams — a pair on each pole row, 2 rows, joins over the poles | 4 lengths |
| 300×50 SG8 H3.27.2 m · Rafters — a pair on every pole line (4 lines), 6.73 m each | 8 lengths |
| BoltsM16 × 350 mm hot-dip galv cup head (coach) bolts, nuts & square washers · 2 at every beam and rafter crossing on a pole | 32 bolts |
| 3 · Roof | |
| Purlins · 240×45 SG8 H1.24.8 m · on edge · 9 rows at ≤900 mm, between the frames | 27 lengths |
| Purlin outriggers / barge purlins240×45 SG8 H3.2 · 3.6 m · Carry the roofing past the end frames | 5 lengths |
| Purlin fixingsLumberlok Purlin Cleat or Multigrip · hot-dip galv · Both sides of every purlin at every frame — check your wind zone | 72 fixings |
| Roof plane bracingGalv strap brace 25 × 1 mm · 30 m roll · Two diagonals on each roof face | 1 rolls |
| Corrugate roofingCOLORSTEEL® · 0.40 BMT · cut to length · 15 sheets · cutting list: 15 × 6.68 m | 100.2 lm |
| Barge flashingMade to order · COLORSTEEL® · 2 sloping edges · 13.3 m + 5% | 14 lm |
| Top edge flashingMade to order · COLORSTEEL® · Along the high side · 11.4 m + 5% | 12 lm |
| Roofing screws12g × 65 mm hex head with washer · Class 4 · 5 per sheet at every purlin (900 mm centres) + 10% | 743 screws |
| Flashing fixingsStitching screws or sealed rivets · box of 100 · 91 · about 1 every 300 mm along the flashings | 1 box |
| 4 · Walls & doors | |
| Girts · 150×50 SG8 H3.26.0 m · on edge · Wall rails between the poles at ≤1100 mm | 16 lengths |
| Girts · 150×50 SG8 H3.24.8 m · on edge · Wall rails between the poles at ≤1100 mm | 9 lengths |
| Girt fixingsLumberlok Multigrip or girt cleats · hot-dip galv · Each end of every girt | 34 fixings |
| Skirt / base boards200×50 H4 · 4.8 m · 22 m along the bottom of the clad walls, less doorways | 5 lengths |
| Corrugate wall claddingCOLORSTEEL® · 0.40 BMT · cut to length, run vertically · 31 sheets · cutting list: 2 × 3.60 m, 2 × 3.55 m, 2 × 3.45 m, 1 × 3.40 m, 1 × 3.35 m, 2 × 3.25 m, 2 × 3.20 m, 2 × 3.15 m, 15 × 3.05 m, 1 × 1.40 m, 1 × 1.35 m | 95.65 lm |
| Wall cladding screws12g × 50 mm hex head with washer · Class 4 · 4 per sheet at every girt + 10% | 546 screws |
| Corner flashingsMade to order · COLORSTEEL® · 2 outside corners | 7.5 lm |
| Edge flashingsMade to order · COLORSTEEL® · Where a clad wall stops at an open side | 7.5 lm |
| Door & window flashingsMade to order · head, jambs & sills · COLORSTEEL® · Round every opening | 6.2 lm |
| Hinged steel skin door800 × 2000 mm · pre-hung · Confirm the frame size with your supplier | 1 unit |
| 150×50 SG8 H3.26.0 m · Door & window framing — jambs, heads and sills | 1 lengths |
| 5 · Floor, lining & spouting | |
| Marley Stormcloud® spoutingWhite · 5 m · MS1.5 | 2 lengths |
| Marley Stormcloud® spoutingWhite · 1.5 m | 1 lengths |
| Spouting bracketsWhite · MS2 · Every 500 mm + each end | 24 brackets |
| Spouting joinersWhite · MS5 · Where lengths join | 2 joiners |
| Stop ends · left handWhite · MS3 | 1 stop ends |
| Stop ends · right handWhite · MS4 | 1 stop ends |
| Expansion outletsWhite · 80 mm · MS8-80 · One per downpipe | 1 outlets |
| RP80® downpipeWhite · 3 m lengths · 1 downpipe × ≈3 m | 1 lengths |
| RP80® bendsWhite · M+F · 2 per offset + 1 at the bottom | 3 bends |
| RP80® downpipe clipsWhite · First within 200 mm of the bend, then max 1.2 m apart | 4 clips |
| Stainless screwsFor downpipe clips · 2 per clip | 8 screws |
| Stainless screwsFor spouting brackets · 3 per bracket (min. 6g × 20 mm, per Marley) | 72 screws |
| Marley MCS® solvent cementWhite · ≈12 joints · don’t glue into expansion outlets or joiners | 1 tins |
This is the list Takeoff produced for that job. Your list will change with your sizes and settings.
Check before you buy
- Tick “The site is in a rural zone” only if your district plan zones it rural (not rural-residential) — the exemption doesn’t apply anywhere else, including in town.
- 151 bags of footing concrete is a lot of mixing — a ready-mix truck (1.6 m³) is usually cheaper (change it under Adjust specs).
- Purlins: 240×45 on edge at 900 mm centres span up to 3.9 m (NZS 3604 Table 10.11) — your bays are 3.6 m.
- No roof underlay or netting listed (open farm shed). Add it for an enclosed shed you want to keep dry and drip-free — tick “Roof underlay & netting”.
- Pole shed exemption (Building Act Schedule 1): rural zone only, single storey, no more than 110 m², no more than 4 m high above the floor, roof spans no more than 6 m, not open to the public, wind zone up to High — and it must be designed or reviewed by a Chartered Professional Engineer, or designed and built (or supervised) by a Licensed Building Practitioner. District plan rules still apply.
- Pole, beam, rafter and girt sizes are typical for a light-roofed shed in a high wind zone and exposure zone C — a starting point for your LBP or engineer, not a design. Have them confirm sizes, embedment and fixings before you order.
What the calculator covers
- Mono-pitch (lean-to) or gable roofs
- Clearspan gable trusses with no middle poles — flagged for an engineer over 6 m
- Any side open or clad in iron
- Roller doors, PA doors and windows
- Pole lengths from the height and embedment
- Wall iron cutting list that follows the roof slope
- Ply lining — untreated or H3.2 — to 1.2 m or full height
- Dirt, basecourse or concrete slab floor
- Checks for the farm shed exemption — 110 m², 4 m high, 6 m spans, wind zone up to High
Questions
Do I need a building consent for a pole shed?
Not always. Single-storey pole sheds and hay barns in a rural zone can be exempt if they are no more than 110 m², no more than 4 m high above the floor, have roof spans of 6 m or less, are not open to the public and are in a wind zone up to High. The design must be done or reviewed by a Chartered Professional Engineer, or designed and built (or supervised) by a Licensed Building Practitioner. In town, it needs a consent.
What size poles do I need for a pole shed?
Most small farm sheds use 150–200 mm SED H5 round poles set about 1.2 m into concreted holes. The right size and depth depend on the height, the bay width, the wind zone and the soil — your LBP or engineer confirms it.
How far apart should pole shed poles be?
Bays of 3.6 to 6 m are common. Wider bays mean fewer poles but bigger beams and purlins, and the exemption allows roof spans of no more than 6 m.
How do I find my wind zone?
Your council can tell you, it is often on the LIM, and BRANZ Maps gives a guide for any address. The pole shed exemption only covers Low, Medium and High wind zones.
Get your own list in under a minute
Put in your sizes. Print it, save it as a PDF, email it or take it to your supplier.
Start your pole sheds & farm sheds list