How to work it out
Decking boards
Work out how many rows of boards fit across the deck (board width plus the gap), then how many lengths each row needs. Takeoff plans the joins so they land on joists and adds 10% for waste and offcuts.
Joists
Joists run across the bearers at 450 mm centres for most pine and hardwood decking. Count the joists along the deck, then buy lengths that cover the span without wasting a metre.
Bearers and piles
Bearers sit on piles, usually at around 1.2–1.3 m centres. The number of bearers depends on the joist span you allow. Pile length depends on how high the deck sits.
Fixings
Every joist–bearer crossing needs a fixing, every pile needs a pile fixing, and every board needs two screws or nails at each joist. That is where most hand-written lists come up short.
Worked example
A 6 × 4 m back deck, 600 mm off the ground, in 90 × 19 pine with 4.8 m boards. Everything else is on the default settings.
| Item | Qty |
|---|---|
| Decking | |
| Decking boards90×19 Pine H3.2 · Premium · Smooth · 4.8 m lengths · 205.9 lm incl. 10% waste | 43 lengths |
| Framing | |
| Joists140×45 H3.2 · 4.8 m · @ 450 mm centres | 12 lengths |
| Boundary joists140×45 H3.2 · 4.8 m · Along both long edges of each area | 2 lengths |
| Bearers100×100 RS H3.2 · 6.0 m | 4 lengths |
| Foundations | |
| Piles125×125 H5 · 750 mm · At 1.3 m centres along each bearer | 20 piles |
| Pile concrete20 kg premix concrete bags · 1.1 m³ incl. 10% waste | 116 bags |
| Fixings | |
| Decking screwsStainless or galv decking screws · box of 1000 · 983 screws needed | 1 box |
| Lumberlok Multigrip38×38×125 · stainless steel · One each time a joist crosses a bearer (+5%) | 51 multigrips |
| Lumberlok product nails30×3.15 · stainless · 500 g bag · ≈408 nails, every hole filled (≈250 per bag) | 2 bags |
| Lumberlok Ordinary Pile FixingStainless steel · bag of 10 sets (wire dogs + nails) · 20 piles · one set each | 2 bags |
| Framing gun nails90×3.15 galv · pack of 1000 · ≈258 nails | 1 pack |
| Finish | |
| Decking oilPine deck oil/stain · ≈10 m²/L per coat, 2 coats | 4 litres |
This is the list Takeoff produced for that job. Your list will change with your sizes and settings.
Check before you buy
- 116 bags of pile concrete is a lot of mixing — a small ready-mix load (1.2 m³) may be cheaper and faster.
- Stainless fixings listed: the bottom of the bearers is less than 600 mm off the ground on Main deck (241 mm). Brackets and fixings there must be stainless steel.
- Anchor and braced piles need a 12 kN fixing — swap those piles to Lumberlok 12kN Pile Fixing (one pack each).
- Decks no more than 1.5 m above ground are generally consent-exempt, but must still meet the Building Code.
- Checked against NZS 3604: 140×45 joists at 450 mm span up to 2.35 m (Table 7.1(b)) — yours are 1.2 m; the bearers with piles at 1.3 m carry up to 1.2 m of joists (Table 6.4(b)). Decks over 2 m out from the house need braced piles (7.4.2).
What the calculator covers
- Joists and bearers checked against NZS 3604 Tables 7.1 and 6.4
- Several deck areas at different heights
- Steps
- Pine, kwila or composite decking
- Random lengths sold by the metre
- Lumberlok Multigrips, pile fixings and nails
- Stainless fixings when the bearers are under 600 mm off the ground
- Pile concrete in bags or ready-mix
- Decking oil
Questions
How many decking boards do I need?
Divide the deck width by the board cover (board width plus the gap) to get the number of rows, then work out how many lengths each row needs. For the 6 × 4 m example on this page that comes to 60 lengths of 4.8 m, 90 mm board, including 10% waste. Takeoff does this for any size.
Do I need stainless steel fixings on my deck?
Takeoff lists stainless brackets and fixings when the bottom of the bearers is less than 600 mm off the ground, in line with NZS 3604. Above that, hot-dip galvanised is the usual choice inland. Near the coast, check the exposure zone for your site.
Do I need a building consent for a deck?
Decks no more than 1.5 m above the ground are generally exempt from consent, but they still have to meet the Building Code. A deck with a fall of 1 m or more needs a barrier. Check with your council if you are unsure.
Get your own list in under a minute
Put in your sizes. Print it, save it as a PDF, email it or take it to your supplier.
Start your decks list