How to work it out
Area
Walls: the distance round the room × the stud height, less doors and windows. Ceilings: length × width. Outside: wall length × height, plus any gable ends, less doors and windows.
Litres
Area × number of coats ÷ coverage per litre. 42 m² of walls, two coats at 11 m²/L, is 42 × 2 ÷ 11 = 7.6 L. Takeoff adds 10% for spills, tray waste and touch-ups.
Coverage
Takeoff uses typical NZ label figures: about 11 m²/L for interior low sheen, 10 for ceiling flat, 12 for enamel and exterior acrylic. Some brands quote up to 16 m²/L. Rough and porous surfaces use more.
Tins
Litres become the cheapest usual mix of 10, 4, 2 and 1 L tins. A bigger tin is often cheaper than two smaller ones, so you may end up with some left for touch-ups.
Worked example
A 5 × 4 m lounge and a 3.6 × 3 m bedroom with 2.4 m studs. Walls, ceilings and trim, two coats over sound existing paint.
| Item | Qty |
|---|---|
| Walls | |
| Interior acrylic · low sheen10 L tin · ≈13.3 L needed (66.6 m² × 2 coats at 11 m²/L) | 1 tin |
| Interior acrylic · low sheen4 L tin | 1 tin |
| Ceilings | |
| Ceiling paint · flat10 L tin · ≈6.8 L needed (30.8 m² × 2 coats at 10 m²/L) · 10 L bought | 1 tin |
| Trim | |
| Interior enamel · gloss or semi-gloss (trim & doors)2 L tin · ≈1.4 L needed (7.4 m² × 2 coats at 12 m²/L) · skirting, architraves, door faces | 1 tin |
| Prep | |
| Sugar soapConcentrate · dilute to label · Wash walls and trim before painting | 1 bottle |
| Patching compoundInterior · small tub · Fill holes and dents | 1 tub |
| Gap fillerPaintable acrylic · cartridge · Gaps along skirting, architraves and cornice | 1 cartridge |
| Sandpaper180–240 grit · pack | 1 pack |
| Tools | |
| Roller frame230 mm | 1 frame |
| Roller sleeves230 mm · medium pile · One for each paint: walls, ceiling | 2 sleeves |
| Roller tray230 mm | 1 tray |
| Extension pole1.2–2.4 m · For ceilings | 1 pole |
| Brushes63 mm cutting-in brush + 50 mm trim brush | 1 set |
| Drop sheetsCanvas or plastic | 2 sheets |
| Masking tapeLow-tack · 24 mm | 1 roll |
This is the list Takeoff produced for that job. Your list will change with your sizes and settings.
Check before you buy
- Coverage rates are typical NZ label figures: interior low sheen about 11 m²/L, ceiling flat about 10, enamel about 12, wallboard sealer about 12. Some brands quote up to 14–16 m²/L — if yours does, change it under Adjust specs.
- Each door counts one face of the door leaf per room. Bare timber or MDF trim needs an undercoat first.
- Tins are the cheapest usual mix of 10, 4, 2 and 1 L for the litres needed — a bigger tin is often cheaper than two small ones. Leftover paint keeps for touch-ups.
- Bright, deep or big colour changes often need an extra coat — the paint shop can tell you when tinting.
What the calculator covers
- Inside: walls, ceilings, trim and doors, room by room
- Outside: walls, gable ends, eaves, fascia and facings
- New plasterboard sealer, or primer for bare surfaces
- Weatherboard, smooth, rough sawn or block cladding
- 1, 2 or 3 top coats
- Your own coverage rates if your paint differs
- Rollers, brushes, drop sheets, tape, filler and sugar soap
Questions
How much paint do I need for a room?
Work out the wall area (distance round the room × stud height, less doors and windows), multiply by the number of coats and divide by the coverage on the tin. For the lounge and bedroom on this page that is about 13 L for the walls and 7 L for the ceilings, with two coats.
How far does a litre of paint go?
Most NZ interior and exterior acrylics list 10–12 m² per litre per coat on the label. Some brands quote up to 16. Rough, porous or bare surfaces use more, so check the label for the paint you buy.
How many coats of paint do I need?
Two top coats is normal. New plasterboard needs a sealer coat first, and bare timber needs a primer. Bright, deep or big colour changes can need a third coat.
Get your own list in under a minute
Put in your sizes. Print it, save it as a PDF, email it or take it to your supplier.
Start your paint list